• 18764172899
    0531一85977876

  • [field:companyname]
    全国咨询热线
当前位置:首页 - 新闻资讯 > 常见新闻 >

断桥铝门窗设备出现供电不稳定的影响

来源:http://www.tianxincnc.cn/ 发布时间:2021-12-16
(1)设备停机。尽管没有形成物理损坏,但容易可编程控制器的程序或逻辑失常、数据丢失或软件损坏。CNC数据(报括操作体系、参数、程序等)不得不从头建立或更换PLC等。供电不稳定也会造成设备的电脑意外死机、锁死或非正常触发设备NC—PLC复位、CNC体系停止响应等问题,致使设备运行不稳定。重新将电脑复位(通常是关机)才能使软件恢复正常作业。
(1) Equipment shutdown. Although there is no physical damage, it is easy to cause program or logic disorder, data loss or software damage of PLC. CNC data (including the operating system, parameters, programs, etc.) have to establish or replace the PLC from the beginning. Unstable power supply will also cause the computer of the equipment to crash unexpectedly, lock or abnormally trigger the nc-plc reset of the equipment and the stop response of the CNC system, resulting in the unstable operation of the equipment. Only by resetting the computer (usually shutdown) can the software resume normal operation.
(2)设备功能下降。如果长时间存在电压不稳定(电压波动过大),会造成设备电子元件和电路功能下降,电子元器件使用寿命降低,使门窗设备整体运行寿命缩短,这些也是普遍存在各门窗企业内的问题。
(2) Equipment function degradation. If there is voltage instability for a long time (excessive voltage fluctuation), it will reduce the function of equipment electronic components and circuits, reduce the service life of electronic components, and shorten the overall operation life of door and window equipment. These are also common problems in door and window enterprises.
,断桥铝门窗加工设备
(3)设备元器件损坏。供电不稳或经常断电可造成各电子元件的损坏,如CPU、I/O接口电路板、驱动电路板、CRT或LCDLED监视器,存储设备如RAM、硬盘和通讯接口等。严重的瞬时过电压会造成门窗设备的电子元件或电路板烧坏,从而影响设备正常运行。
(3) Equipment components are damaged. Unstable power supply or frequent power failure can cause damage to various electronic components, such as CPU, I / O interface circuit board, drive circuit board, CRT or lcled monitor, storage devices such as RAM, hard disk and communication interface. Serious instantaneous overvoltage will burn out the electronic components or circuit board of door and window equipment, thus affecting the normal operation of the equipment.
塑钢门窗设备从大体上来讲有切割、焊接、清洁类设备,另外还有一些铣削设备,这种设备主要用来加工门窗的凹槽和门窗锁孔的,这是门窗的加工过程所决定的,每一种设备都有自己独特的用处,因此这些设备在某种程度上来讲,都是必要的,同时选择品质好的门窗加工设备,才能制作更高品质的塑钢门窗。
Generally speaking, plastic steel door and window equipment includes cutting, welding and cleaning equipment, as well as some milling equipment. This equipment is mainly used to process the grooves and lock holes of doors and windows, which is determined by the processing process of doors and windows. Each equipment has its own unique use, so these equipment are necessary to some extent, At the same time, only by selecting high-quality door and window processing equipment can we make higher quality plastic steel doors and windows.