• 18764172899
    0531一85977876

  • [field:companyname]
    全国咨询热线
当前位置:首页 - 新闻资讯 > 常见新闻 >

如何使用和操作断桥铝门窗设备双头?

来源:http://www.tianxincnc.cn/ 发布时间:2021-10-08
如何使用和操作断桥铝门窗设备双头锯?这是门窗加工制作工人需要掌握的重 点部分,
How to use and operate the double head saw of bridge broken aluminum door and window equipment? This is the key part that the processing and manufacturing workers of doors and windows need to master,
(1)调整压紧气缸的位置
(1) Adjust the position of the hold down cylinder
将铝合金型材放到该铝门窗设备的工作台面上,两锯头的压紧气缸调整至对工件压紧合适的位置,然后固定压紧气缸。
Put the aluminum alloy profile on the worktable of the aluminum door and window equipment, adjust the pressing cylinder of the two saw heads to the appropriate position for pressing the workpiece, and then fix the pressing cylinder.
(2)调整锯片进给速度
(2) Adjust the feed speed of saw blade
先以切割锯出厂的默认锯片进给速度试机,在试机过程中,如果觉得锯片的进给速度不合适时,可以调节工进气缸调速接头,增 大或减少进给速度,就可得到所需要的进给速度。
First test the machine with the default feed speed of the cutting saw. During the test, if you feel that the feed speed of the saw blade is inappropriate, you can adjust the speed regulating joint of the feed cylinder to increase or reduce the feed speed, and you can get the required feed speed
断桥铝门窗加工设备
.
(3)调整锯削角度
(3) Adjust sawing angle
铝合金型材精 密切割锯按上述各项调整完毕,检查符合规定后试运转30分钟。
The precision cutting saw for aluminum alloy profile shall be adjusted according to the above items, and the test run shall be conducted for 30 minutes after it is checked to meet the requirements.
(4)调整设备90°角的切割(锯片伸出与工作台面垂直)。
(4) Adjust the 90 ° cutting angle of the equipment (the saw blade extends perpendicular to the worktable).
铝合金型材精 密切割锯出厂前均经调试并经检验合格,在此可直接锯切一铝合金型,材检验其90度角的锯切面是否符合要求,误差为±10′。如若不符合要求,可调整限位挡块上的螺栓。然后再重复锯切测量,使之满足要求。
Before leaving the factory, the precision cutting saw of aluminum alloy profile has been debugged and passed the inspection. Here, an aluminum alloy profile can be directly sawed to check whether the 90 degree sawing surface meets the requirements, and the error is ± 10 '. If the requirements are not met, the bolts on the limit stop can be adjusted. Then repeat the sawing measurement to meet the requirements.
(5)调整设备45°角的切割(锯片伸出与工作台面夹角成45°时设定为45°)
(5) Adjust the cutting angle of 45 ° of the equipment (set to 45 ° when the angle between the saw blade and the worktable is 45 °)
松开工作台上的锁紧手柄,摆角气缸通气,45度角到位后,锁紧把手。锯切型材后检查是否符合要求(误差为±10′)。如果不符合要求,可调整限位挡块上的限位螺钉,重复锯切、测量,使之满足要求。然后再锁紧螺钉上的螺母,拧紧锁紧手柄。
Loosen the locking handle on the workbench, swing the air cylinder for ventilation, and lock the handle after the 45 degree angle is in place. After sawing the profile, check whether it meets the requirements (the error is ± 10 '). If it does not meet the requirements, adjust the limit screw on the limit stop, and repeat sawing and measurement to make it meet the requirements. Then lock the nut on the screw and tighten the locking handle.
(6)调整型材切割长度。
(6) Adjust the cutting length of profile.
角度调整完毕后,应调整铝合金型材的切割长度。拉动把手带动右锯头沿圆导轨移动至准确位置(看标尺指针),刻度尺指示长度即铝合金型材短边的长度。切割完成后,如切割后型材的长度与要求长度有偏差,应进行微调,微调时,拧紧刹车可调手炳,转动微调手炳至要求尺寸。
After the angle adjustment, the cutting length of aluminum alloy profile shall be adjusted. Pull the handle to drive the right saw head to move to the accurate position along the circular guide rail (see the scale pointer). The scale indicates the length, that is, the length of the short side of the aluminum alloy profile. After cutting, if the length of the cut profile deviates from the required length, fine adjustment shall be carried out. During fine adjustment, tighten the brake adjustable handle and turn the fine adjustment handle to the required size.