• 18764172899
    0531一85977876

  • [field:companyname]
    全国咨询热线
当前位置:首页 - 新闻资讯 > 行业新闻 >

门窗设备出现供电不稳定会出现哪些故障?

来源:http://www.tianxincnc.cn/ 发布时间:2021-09-13
门窗制造企业在生产过程中,门窗设备供电会出现各式各样的问题,其实这些都是很正常的,下面对经常断电或电压不稳定给设备造成的伤害做一下阐述,希望引起各门窗生产企业的注意。供电不稳定除给企业生产造成影响外,对门窗加工设备也会造成一定的伤害:
In the production process of door and window manufacturing enterprises, there will be various problems in the power supply of door and window equipment. In fact, these are very normal. The following describes the damage to the equipment caused by frequent power failure or unstable voltage, hoping to attract the attention of door and window manufacturing enterprises. Unstable power supply will not only affect the production of enterprises, but also cause certain damage to door and window processing equipment:
(1)设备停机。尽管没有形成物理损坏,但容易可编程控制器的程序或逻辑失常、数据丢失或软件损坏。CNC数据(报括操作体系、参数、程序等)不得不从头建立或更换PLC等。供电不稳定也会造成设备的电脑意外死机、锁死或非正常触发设备NC—PLC复位、CNC体系停止响应等问题,致使设备运行不稳定。重新将电脑复位(通常是关机)才能使软件恢复正常作业。
(1) Equipment shutdown. Although there is no physical damage, it is easy to cause program or logic disorder, data loss or software damage of the programmable controller. CNC data (including operating system, parameters, programs, etc.) have to be established or replaced from scratch. Unstable power supply will also cause the computer of the equipment to crash unexpectedly, lock or trigger the nc-plc reset of the equipment abnormally, and the CNC system stops responding, resulting in the unstable operation of the equipment. Reset the computer (usually shut down) to restore the normal operation of the software.
(2)设备功能下降。如果长时间存在电压不稳定(电压波动过大),会造成设备电子元件和电路功能下降,电子元器件使用寿命降低,使门窗设备整体运行寿命缩短,这些也是普遍存在各门窗企业内的问题。
(2) The function of the device decreases. If there is voltage instability for a long time (excessive voltage fluctuation), it will reduce the function of electronic components and circuits of the equipment, reduce the service life of electronic components, and shorten the overall operation life of door and window equipment. These are also common problems in door and window enterprises.
(3)设备元器件损坏。供电不稳或经常断电可造成各电子元件的损坏,如CPU、I/O接口电路板、驱动电路板、CRT或LCDLED监视器,存储设备如RAM、硬盘和通讯接口等。严重的瞬时过电压会造成门窗设备的电子元件或电路板烧坏,从而影响设备正常运行。
(3) Equipment components are damaged. Unstable power supply or frequent power failure can cause damage to electronic components, such as CPU, I / O interface circuit board, drive circuit board, CRT or lcled monitor, storage devices such as RAM, hard disk and communication interface. Serious instantaneous overvoltage will burn out the electronic components or circuit boards of door and window equipment, thus affecting the normal operation of the equipment.
所以各门窗企业在设备使用过程中,一定要保证车间供电的稳定性,避免门窗设备故障,动力线和照明线要分开,车间设备要良好的接地。并且要按设备的操作规程,操作、保养设备,不得违规操作、野蛮操作,而且要及时、定期的对设备进行维护和保养,避免带病作业,只有这样才能够避免设备频繁出现故障,提高设备的使用寿命及工作效率。
Therefore, in the process of equipment use, all door and window enterprises must ensure the stability of workshop power supply, avoid door and window equipment failure, separate power lines and lighting lines, and well grounded workshop equipment. In addition, the equipment shall be operated and maintained according to the operating procedures of the equipment, and illegal operation and barbaric operation are not allowed. In addition, the equipment shall be maintained and maintained timely and regularly to avoid sick operation. Only in this way can the frequent failure of the equipment be avoided and the service life and work efficiency of the equipment be improved.