• 18764172899
    0531一85977876

  • [field:companyname]
    全国咨询热线
当前位置:首页 - 新闻资讯 > 公司动态 >

保养铝门窗加工设备需要注意什么?

来源:http://www.tianxincnc.cn/ 发布时间:2022-01-24
良好的操作习惯是非常重要的,操作人员在操作设备中对铝门窗设备有一定的了解,包括操作设备的控制方式和各种技术指标,在启动过程中对设备零件进行检查,包括是否有碎片、机械零件、加工零件、操作零件是否正常。
Good operating habits are very important. Operators have a certain understanding of aluminum door and window equipment in operating the equipment, including the control mode and various technical indicators of operating the equipment, and check the equipment parts during startup, including whether there are fragments, mechanical parts, processed parts and whether the operating parts are normal.
使用中的设备环境也很重要,一般设备环境以干燥清洁的环境为主,断桥铝门窗设备的维护、维护方式很重要,首先定期清洗,每次设备加工中,都会在设备的各个构成部件上留下各种琐碎的东西,经过时间的积累,各个部件都会形成特殊的杂质组
The equipment environment in use is also very important. Generally, the equipment environment is mainly dry and clean. The maintenance and maintenance method of broken bridge aluminum door and window equipment is very important. First, it is cleaned regularly. In each equipment processing, various trivial things will be left on each component of the equipment. After the accumulation of time, each component will form a special impurity group
使用专用润滑油润滑设备的连接部位,同时根据平时的加工需要对门窗设备进行进料和调试,如调试切割设备的紧固程度和切割角度,适当调整导轨的精度,设备的电路也可以在使用过程中进行维修。
Use special lubricating oil to lubricate the connecting parts of the equipment. At the same time, feed and debug the door and window equipment according to the usual processing needs, such as debugging the fastening degree and cutting angle of the cutting equipment, properly adjusting the accuracy of the guide rail, and the circuit of the equipment can also be repaired during use.
断桥铝门窗加工设备
维修设备需要遵循由外而内的原则,检查设备外部是否有明显的裂痕、缺损,,然后再对其内部进行检测,拆前应排队周边的故障因素,确定为机内故障后才能拆卸,否则盲目拆卸,可能将门窗加工设备越修越坏,先机械后电,气只有在确定机械零件无故障后,再进行电气方面的检查,检查电路故障时,应利用检测仪器寻找故障部位,确认无接触不良故障后,再有针对性地查看线路与机械的运作关系,以免判断失误。
The maintenance equipment shall follow the principle of "from the outside to the inside", check whether there are obvious cracks and defects on the outside of the equipment, and then inspect its inside. Before disassembly, queue up the surrounding fault factors, and disassemble it only after it is determined that it is an internal fault. Otherwise, blind disassembly may damage the door and window processing equipment more and more. Machinery first and then electricity, and gas only after it is determined that there is no fault on the mechanical parts, Then conduct electrical inspection. When checking the circuit fault, use the detection instrument to find the fault part. After confirming that there is no poor contact fault, check the operation relationship between the line and the machinery, so as to avoid misjudgment.
设备先不要通电,判断设备的按钮、线路等是否出现问题,从而判定故障的所在,通电试验,听其声、测参数、判断故障,之后进行维修,如在电动机缺相时,若测量三相电压值无法着判别时,就应该听其声,单独测每相对地电压,方可判断哪一相缺损,先清洁后维修,对污染较重的断桥铝门窗设备,先对其按钮、接线点、接触点进行清洁,检查外部控制键是否失灵,许多故障都是由脏污及导电尘块引起的,一经清洁故障往往会排除。
Do not energize the equipment first, judge whether there is a problem with the buttons and lines of the equipment, so as to determine the fault. Conduct the power on test, listen to the sound, measure the parameters and judge the fault, and then carry out maintenance. If the three-phase voltage value cannot be judged when the motor is out of phase, you should listen to the sound and measure the voltage of each phase to ground separately, so as to judge which phase is out of phase, Clean before maintenance. For the heavily polluted broken bridge aluminum door and window equipment, clean its buttons, wiring points and contact points first, and check whether the external control keys fail. Many faults are caused by dirt and conductive dust. Once cleaned, the faults are often eliminated.
数控门窗设备专注为您提供新鲜的行业资讯,更多的问题及精彩内容请关注我们的网站:http://www.tianxincnc.cn ,我们会有更多的精彩内容为您呈
CNC door and window equipment focuses on providing you with fresh industry information. For more questions and wonderful contents, please pay attention to our website: http://www.tianxincnc.cn , we will have more wonderful content for you