• 18764172899
    0531一85977876

  • [field:companyname]
    全国咨询热线
当前位置:首页 - 新闻资讯 > 公司动态 >

炎热的天气如何清洗门窗加工设备?

来源:http://www.tianxincnc.cn/ 发布时间:2021-08-25
为了让客户能更好的运用设备,特意整理出以下几条留意事项,为您供给一套冬天门窗设备保护保养方案,供广大行业读者参阅!
In order to enable customers to make better use of the equipment, we have specially sorted out the following precautions to provide you with a set of protection and maintenance scheme for door and window equipment in winter for the readers of the industry!
一:铣切类设备(双头切开锯、端铣、仿形铣、角码锯、铝木铣榫机、铝木铣形机、90度切开锯等)
1: Milling and cutting equipment (double head cutting saw, end milling, profiling milling, corner code saw, aluminum wood tenon milling machine, aluminum wood milling machine, 90 degree cutting saw, etc.)
1、每天下班后,要把铝型材设备上的铝(木)屑整理干净,特别是设备的传动部位和活动部位(例如:导轨,气缸,工作面板等);
1. Clean up the aluminum (wood) chips on the aluminum profile equipment after work every day, especially the transmission parts and moving parts of the equipment (such as guide rail, cylinder, work panel, etc.);
2、定时检查设备各部位螺丝,避免呈现松动,导致精度差错和安全事故。
2. Regularly check the screws at all parts of the equipment to avoid looseness, resulting in accuracy errors and safety accidents.
3、定时为设备各传动轴擦抹润滑油(例如:直线导轨);
3. Regularly wipe lubricating oil for each transmission shaft of the equipment (e.g. linear guide rail);
4、铝机挑选较稀释的切削液,不主张兑水;
4. Aluminum machine selects more diluted cutting fluid and does not advocate mixing with water;
5、每天开工前检查设备气路和电磁阀阀体有存水现象,保证气路晓畅后运用设备。为避免呈现气路有水,必定要做到空气压缩机每天放水,常常替换滤芯等。
5. Check whether there is water in the air circuit and solenoid valve body of the equipment before commencement every day to ensure that the equipment can be used after the air circuit is smooth. In order to avoid water in the air circuit, it is necessary to discharge water from the air compressor every day and often replace the filter element.
6、每天检查电源开关是否正常,电线是否老化,如有问题,当即替换。
6. Check whether the power switch is normal and whether the wire is aging every day. If there is any problem, replace it immediately.
7、铝型材、木材等轻拿轻放,避免呈现磕碰,导致设备损坏呈现差错等。
7. Handle aluminum profile and wood with care to avoid collision, resulting in equipment damage, error, etc.
8、禁止戴手套作业的设备,禁止戴手套作业。不能穿戴围巾等相似衣物,避免呈现安全事故。
8. It is forbidden to wear gloves for operation. Do not wear scarves and other similar clothes to avoid safety accidents.
9、定时检查电源线、电磁阀等电器元件,避免呈现短路等严重事故!
9. Regularly check the power cord, solenoid valve and other electrical components to avoid serious accidents such as short circuit!
10、设备运转时留意设备运转状态,避免电动机、油压设备温度过高,呈现异常及时断电、断气,带设备温度康复正常后再运用。
10. During the operation of the equipment, pay attention to the operation state of the equipment to avoid the excessive temperature of the motor and oil pressure equipment, and in case of abnormalities, cut off the power and gas in time, and use the equipment after the temperature of the equipment recovers to normal.